The "WizardProg Mobile" (professional version application is "WizardProg Expert") application software designed to manage the programming operation for the universal portable USB-programmer TL866A/CS and other programmer models which fully compatible with it. This system is used to program a wide range of E(E)PROM chips, microcontrollers internal EEPROM, testing SRAM chips and logic chips.
The application allows you to achieve a new level of mobility and efficiency when using the programmer TL866, which is used widely to repair and adjustment:
· automotive computers, computer-unit and radio;
· personal computers;
· any other modern electronic equipment.
The "WizardProg Mobile" system is used by service technicians of electronics, amateur radio operators and developers of modern electronic devices for the purpose of:
· repair and restore the microelectronic device and firmware;
· promptly update the firmware of microelectronic devices;
· assist in the embedded electronics construction and setting up the microcontroller units;
· replicate numerous useful designs using advanced electronic components.
Main characteristics and features of the "WizardProg Mobile" microelectronic programming system are:
· Fast and reliable programming, in most cases with significantly better speed than the similar systems.
· The programmer's low power consumption when powered by USB (OTG)-cable from the mobile device battery.
· Support for a wide range of integrated circuits (ICs): the memory of a large capacity up to 128Mbit (EPROM, FLASH, EEPROM I2C/3-wire/SPI), microcontrollers PIC, Atmel-AVR, MCS-51 based SST, SyncMOS, Winbond. PLD chips, GAL.
TL866 programmer does not need an external power supply and it operates using the power sources of a tablet or mobile phone which is connected to via USB interface. Physical linking to a mobile device is provided with a USB cable fully supporting OTG (On-The-Go) protocol.
Important note! The target control tablet or mobile phone must have a fully implemented hardware support of OTG access too!
Currently "WizardProg Mobile" mobile application is completely autonomous in operation, does not need a permanent connection to the Internet, allowing you to use it even without access to communication networks.
Both of programmer's models TL866CS and TL866A(ICSP) are fully supported. The modern version of the TL866II Plus programmer currently is not supported by the "WizardProg Mobile" system!
Device list for the current application version: http://www.wizardprog.com/wp/dblist/recent_version_chiplist.htm
"WizardProg Mobile" (aplikasi versi profesional ialah perisian aplikasi "WizardProg Expert") yang direka untuk menguruskan operasi pengaturcaraan untuk pemrogram USB universal programer TL866A / CS dan model pemrogram lain yang serasi sepenuhnya dengannya. Sistem ini digunakan untuk memprogramkan pelbagai jenis cip PROM (E), mikrokontroler EEPROM dalaman, menguji kerepek SRAM dan cip logik.
Aplikasi ini membolehkan anda mencapai tahap mobiliti dan kecekapan baru apabila menggunakan pemrogram TL866, yang digunakan secara meluas untuk pembaikan dan penyesuaian:
· Komputer automotif, unit komputer dan radio;
· Komputer peribadi;
· Sebarang peralatan elektronik moden yang lain.
Sistem "WizardProg Mobile" digunakan oleh juruteknik perkhidmatan elektronik, pengendali radio amatur dan pemaju peranti elektronik moden untuk tujuan:
· Membaiki dan memulihkan peranti mikroelektronik dan firmware;
· Segera mengemas kini firmware peranti mikroelektronik;
· Membantu dalam pembinaan elektronik tertanam dan menubuhkan unit mikrokontroler;
· Meniru pelbagai reka bentuk yang berguna menggunakan komponen elektronik canggih.
Ciri-ciri utama dan ciri-ciri sistem pengaturcaraan Mikroelektronik "WizardProg Mobile" adalah:
· Pengaturcaraan yang cepat dan boleh dipercayai, dalam kebanyakan kes dengan kelajuan yang jauh lebih baik daripada sistem yang serupa.
· Penggunaan kuasa rendah pemrogram apabila dikuasakan oleh USB (OTG) -kabel dari bateri peranti mudah alih.
· Sokongan untuk pelbagai litar bersepadu (IC): memori kapasiti besar sehingga 128Mbit (EPROM, FLASH, EEPROM I2C / 3-wire / SPI), PIC mikrokontroler, Atmel-AVR, SyncMOS, Winbond. Cip PLD, GAL.
Programmer TL866 tidak memerlukan bekalan kuasa luaran dan ia beroperasi menggunakan sumber kuasa tablet atau telefon bimbit yang disambungkan ke melalui antara muka USB. Menyambungkan fizikal ke peranti mudah alih disediakan dengan kabel USB yang menyokong sepenuhnya protokol OTG (On-The-Go).
Nota PENTING! Tablet kawalan sasaran atau telefon bimbit mesti mempunyai sokongan perkakasan yang sepenuhnya dilaksanakan akses OTG juga!
Kini aplikasi mudah alih "WizardProg Mobile" sepenuhnya autonomi dalam operasi, tidak memerlukan sambungan tetap ke Internet, membolehkan anda menggunakannya walaupun tanpa akses kepada rangkaian komunikasi.
Kedua-dua model programmer TL866CS dan TL866A (ICSP) disokong sepenuhnya. Versi moden programmer TL866II Plus kini tidak disokong oleh sistem "WizardProg Mobile"!
Senarai peranti untuk versi aplikasi semasa: http://www.wizardprog.com/wp/dblist/recent_version_chiplist.htm